• 产品简介
• 图片展示

PRODUCT FEATURES: 产品特征：

LXBX series ultra-low temperature separator machine is a

high-tech product which was independently designed and

developed by Lixang Refrigeration Equipment Co., Ltd.

LXBX系列超低温分离机是由立翔制冷设备有限公司自主设计开发的高科技产品。

It is very suitable for various sizes of mobile phones' LCD repair, recycling, refurbishment, rework, etc.

其非常适合各种规格的手机LCD屏维修、回收、翻新、返工等”。

 The lowest temperature of the machine can reach up to -180℃ without using liquid Nitrogen as refrigerant.

在不使用液氮作制冷剂的情况下，机器工作区域的最低温度可达到-180℃.

 It can easily separate out glass, TP, back-light, OCA, LOCA,bracket from damaged LCD module. No need to change the polarizer film.

它可以很容易地将玻璃、TP、背光、OCA胶、LOCA胶、支架等从损坏的液晶模组中分离出来, 不需要更换偏光片。

 High efficiency. No components damage during the LCD module separating process.

高效，并且在液晶模组分离过程中没有元件损坏。

 It is really a good helper for the LCD reparation industry.

它确实是液晶显示器修复行业的一个好帮手。

Operation Instructions: 操作说明

 1.) Before using, it will take the machine around 30～40 minutes to

cool to the set working temperature.

使用前，需要在30~40分钟左右将机器冷却至设定的工作温度。

 2.) Place the LCD screen on the frozen plate.

将液晶屏放置在冷冻板上。

 3.) Freezing time from 30 seconds to 1 minute depends on different LCD screens.

冷冻时间从30秒到1分钟取决于不同类型的液晶屏幕。

 4.) Take out LCD screen and separate it.

取出液晶屏并将其分离开。

5.) Below is the URL of youtube video link for your reference:

以下是优酷视频链接的URL，供您参考：

http://i.youku.com/i/UMzYwNzc0OTg4NA==?spm=a2hzp.8244740.0.0

Tips: 提示

 1. For serious crushed glass, please stick a tape on glass for safety and good for machine.

对于严重的碎玻璃，请用胶带贴在玻璃上，以保证安全，对机器也有好处。

 2. Please make sure the operator wears gloves in case of danger.

请确保操作员戴上手套，以防止危险，

 3. It is much easier to separate out the bracket and other components after freezing processing. Please pay attention to the back-light water inlet.

经过冷冻处理后，分离支架和其他部件要容易得多。请注意背光水口。

 4. After separating the LCD screen, pay attention to the water treatment and temperature recovery.

液晶屏分离后，注意水的处理和温度的回收。

 5. When separating the curved screen, the separation risk caused by the temperature difference between 2 sides of the curved surface

LCD screen. Please pay more attention to this point.

分离曲面屏时，曲面LCD屏幕两侧温差引起的分离风险，请注意到这一点。

 6. After LCD separation, please put the glue side upward to avoid sticking on the article surface after the temperature return to the normal.

液晶屏分离后，请将屏的胶水侧向上放置，以避免杂物粘在屏表面后，并让屏的表面温度恢复正常。

Product Parameters: